Sticker Installation Guides

Small Sticker and Decal Application Instructions

How To Apply A Small Sticker or Decal

Step 1 - Clean the area thoroughly

Step 1

Clean the area thoroughly with rubbing alcohol or soap and water. Do not use Windex or similar products because it will leave a residue behind that will prevent the sticker from adhering well.

Step 2 - Prepare the sticker for application

Step 2

Prepare the sticker for application by firmly rubbing a squeegee or credit card across the clear transfer tape. This removes any air bubbles that may have formed and makes the sticker cling to the transfer tape.

Step 3 - Peel the white paper backing off

Step 3

Peel the white paper backing off the sticker. If the sticker clings to the backing, slowly replace the paper backing and repeat Step 2.

Step 4 - Lower the sticker onto the surface

Step 4

Slowly lower the sticker onto the surface and rub it in place firmly with a squeegee or credit card. For best results, wait 24 hours before moving to the next step.

Step 5 - Slowly peel the clear transfer tape off

Step 5

Slowly peel the clear transfer tape off at an angle. Be careful not to pull the sticker off the surface. If sticker pulls away from the surface repeat Step 4.

Large Cut-Out Sticker Application Instructions

How To Apply A Large Cut-Out Sticker or Decal

Step 1 - Prepare the sticker for application

Step 1

Prepare the sticker for application by firmly rubbing a squeegee or credit card across the clear transfer tape. This removes any air bubbles that may have formed and makes the sticker cling to the transfer tape.

Step 2 - Clean the area thoroughly

Step 2

Clean the area thoroughly with rubbing alcohol or soap and water. Do not use Windex. Measure and place the sticker in the desired location. Put a piece of masking tape on the top of the sticker to hold it in place.

Step 3 - Peel the white paper backing off

Step 3

Lift the sticker up and peel the white paper backing off the sticker. Be careful not to pull the masking tape off. Keep hold of the bottom of the sticker to keep it from sticking to itself or the surface before you want it to.

Step 4 - Lower the sticker and rub it in place

Step 4

Slowly lower the sticker and rub it in place with a squeegee or credit card. Start at the top middle and then the outer edges. Firmly rub the sticker in place to make sure there is no air trapped under the sticker.

Step 5 - Wait 24 hours

Step 5

For best results wait 24 hours then slowly peel the clear cover off at an angle. Be very careful not to pull the sticker off the surface. If the sticker pulls away from the surface repeat step 4. Use a pin to poke any air bubbles in the center and push the air out through the hole.

Large Die-Cut Sticker Application Instructions

How To Apply A Large Contour Die-Cut Sticker or Decal

Step 1 - Clean the area thoroughly

Step 1

Clean the area thoroughly with rubbing alcohol or soap and water. Do not use Windex or similar products because it will leave a residue behind that will prevent the sticker from adhering well.

Step 2 - Place the sticker in the desired location

Step 2

Measure and place the sticker in the desired location. Put a piece of masking tape down the center of the sticker to hold it in place.

Step 3 - Wait 24 hours

Step 3

Lift half of the sticker up and peel off the white paper backing. Hold the sticker taunt but be careful not to pull the masking tape off. Cut the paper backing off.

Step 4 - Lower the sticker

Step 4

Slowly lower the sticker by rubbing it in place with a felt squeegee or a credit card wrapped in a sock. Start at the middle and then work your way out to the edges.

Step 5 - Remove the paper backing

Step 5

Fold the remaining half back and remove the paper backing. Slowly lower the sticker by rubbing it with the felt squeegee or sock covered credit card. Start at the middle and work to outer edges.

*For best results do not apply a sticker in extreme hot or cold temperatures.

Large Windshield Sticker Application Instructions

How To Apply A Large Windshield Sticker or Decal

Step 1 - Prepare the sticker for application

Step 1

Prepare the sticker for application by firmly rubbing a squeegee or credit card across the clear transfer tape. This removes any air bubbles that may have formed and makes the sticker cling to the transfer tape.

Step 2 - Clean the area thoroughly

Step 2

Clean the area with rubbing alcohol or soap and water. Do not use Windex. Place the sticker in the desired location with a piece of masking tape on the top of the sticker to hold it in place. Cut into 3 parts between letters.

Step 3 - Remove the paper backing

Step 3

Lift the sticker up and peel the white paper backing off the sticker. Be careful not to pull the masking tape off. Hold on to the bottom of the sticker.

Step 4 - Lower the sticker

Step 4

Slowly lower the sticker and rub it in place with a squeegee or credit card. Start at the top middle and then the outer edges. Firmly rub the sticker in place to make sure there is no air trapped under the sticker. Repeat for each part.

Step 5 - Wait 24 hours

Step 5

For best results wait 24 hours then slowly peel the clear cover off at an angle. Be careful not to pull the sticker off the surface. If the sticker pulls away from the surface repeat step 4.

Family Sticker Application Instructions

How To Apply A Family Sticker or Decal

Step 1 - Clean the area thoroughly

Step 1

Clean the area where you will place the sticker with rubbing alcohol or soap and water. Do not use Windex.

Step 2 - Prepare the sticker for application

Step 2

Prepare the sticker for application by firmly rubbing a squeegee or credit card across the clear transfer tape. This removes any air bubbles that may have formed and makes the sticker cling to the transfer tape.

Step 3 - Remove the paper backing

Step 3

Peel the white paper backing off the sticker. If the sticker clings to the backing, slowly replace the paper backing and repeat Step 2.

Step 4 - Lower the sticker

Step 4

Slowly lower the sticker and rub it in place with a squeegee or credit card. Start at the top middle and then the outer edges. Firmly rub the sticker in place to make sure there is no air trapped under the sticker.

Step 5 - Wait 24 hours

Step 5

For best results wait 24 hours then slowly peel the clear cover off at an angle. Be careful not to pull the sticker off the surface. If the sticker pulls away from the surface repeat step 4.

*For family-specific instruction videos, visit the videos page.


*Use a pin to poke any air bubbles in the center and push the air out through the hole.
*For best results do not apply a sticker in extreme hot or cold temperatures.